企业信息

    济宁市天通机械设备有限公司

  • 8
  • 公司认证: 营业执照已认证
  • 企业性质:有限责任公司
    成立时间:
  • 公司地址: 山东省 济宁 任城区 唐口街道 唐口工业园
  • 姓名: 范先生
  • 认证: 手机已认证 身份证已认证 微信未绑定

    供应分类

    河南 环保设备 生活污水处理 电解式 质量**

  • 所属行业:水工业 污水处理设备 污水处理成套设备
  • 发布日期:2017-12-29
  • 阅读量:164
  • 价格:100.00 元/台 起
  • 产品规格:定制
  • 产品数量:1500.00 台
  • 包装说明:定制
  • 发货地址:山东济宁任城区唐口街道  
  • 关键词:环保设备,生活污水处理,水处理设备

    河南 环保设备 生活污水处理 电解式 质量**详细内容

    公司简介:济宁天通水处理设备有限公司——通过建立品牌,经过多年的经营和发展,在国内**业取得了良好的成绩。另一方面在更广阔的世界,是行业走出自己特色的道路。其核心产品有:污水处理站、废水处理工艺、废水处理设备、工业废水处理设备、水处理设备、生活污水处理设备、环境污水处理设备等设备。济宁“天通”品牌产品**欧盟、东盟和中东,和济宁的快打下了坚实的基础,新的、更高的发展。
    生活污水处理设备
    生活污水处理设备的设计主要是针对生活污水和与之类似的工业**污水的处理,其主要处理手段是采用目前较为成熟的生化处理技术-接触氧化法,水质参数按一般生活水质,进水BOD200mg/1,出水BOD200mg/1指标设计,
    总共有六部分组成:调节池;接触氧化池;二沉池;消毒装置;污泥处理机;风机,
     
    以下我们进行生活污水处理设备的各个单元的详细说明:
    初沉池:初沉池为竖流式沉淀池,污水在深沉池的上升流速为0.6-0.7毫米/秒,让大颗粒污泥沉淀下来,降低后续生化处理的负荷,沉淀的污泥通过污泥管道提升至调节池,实现再一次循环的处理;
    2、接触氧化池:初沉后水自流至接触池进行生化处理,接触池分三级,总停留时间为1小时以上,其中加强型设备接触氧化时间可达6小时,填料为新颖填料,易结膜,不堵塞。填料比表面积为160m2/m3,接触池气水比在12:1左右;
    3、二沉池:生化后污水流到二沉池,二沉池为二只竖流式沉淀池,它们并联运行。上升流速为0.3-0.4毫米/秒。排泥采用空气提升至污泥装置;
    4、消毒池装置:消毒池按规范:“TJ14-74”标准为30分钟,若是医院污水,消毒池可增加停留时间至1-1.5小时,采用固体氯片接触溶解的消毒方式。消毒装置能根据出水量的大小不断改变加药量,达到多出水多加药,少出水少加药的目的。其它消毒装置可另行配制;
    5、污泥装置:污泥池清液回流至热交换氧化池内进行再处理,消化后剩余污泥很少,一般1-2年清理一次,清理方法采用吸粪车从污泥池的检查孔伸入污泥底部,进行抽吸外运即可。也可以通过循环处理掉;
    6、风机:风机设在消毒的上方,进口采用双层隔音,进风口有消声器、风机过滤器,因此运行时无噪音;单台风机运行寿命30000小时左右。
     
    生活污水处理设备的应用特征:
    (1)适用范围:适用于住宅区、饭店、宾馆、疗养院、学校、矿山、工厂等生活污水处理及类似的工业污水处理。
    (2)设备特点:集处理BOD5、COD、NH3-N、粪大肠杆菌、PH于一身;污水处理设备可地表安装,也可以埋入地下;产生的嗓声低异味少,对周围环境的影响小;净化程度高,整套系统污泥产生量少;自动化程度高,管理方便,不需要专人管理;技术稳定,维护方便;能耗低,节省运行成本。
    (3)型号规格:清之源生产的生活污水处理设备,有固定规格的一体化设备六种型号;还有根据根据生活污水水量或水质进行设计制造的成套设备。
    (4)工艺说明:生活污水处理设备的设计主要是对生活污水和与之相类似的工业**污水处理,其主要处理方法是采用较为成熟的生化处理生物接触氧化法,水质设计参数按照一般生活污水水质设计计算,进水BOD5平均值为200mg/L,出水BOD5平均值为20mg/L。
    a、水解调节池不在设备内,需用户另建,池内须装粗、细格栅各一道,以拦截污水中的粗渣和较大悬浮物。
    b、生物接触氧化池内中部挂满组合填料;底部装有SLB型射流曝气机2台,一台为定时自动曝气,一台随提升泵联动工作。
    c、沉淀池为斜板式,池内进、出水管均采用多排孔布水、集水,使水流状态稳定;池底为“V”型斜底并设有两根多孔排泥管,池内污泥每3-6个月由水泵或粪车抽出外运。
    Company profile: Jining Tian Tong water treatment equipment Co., Ltd. -- through establishing brand, after years of operation and development, it has achieved good results in the same industry in China. On the other hand, in the wider world, it is the path of the industry to get out of its own characteristics. Its core products are: sewage treatment station, wastewater treatment process, wastewater treatment equipment, industrial wastewater treatment equipment, water treatment equipment, domestic sewage treatment equipment, sewage treatment equipment and other equipment. Jining "Tian Tong" brand products are exported to the EU, ASEAN and the Middle East, and Jining have laid a solid foundation, new and higher development.
    Domestic sewage treatment equipment
    The design of the sewage treatment equipment is mainly for sewage and similar treatment of industrial organic wastewater, the main processing means is the use of the biochemical treatment technology - mature contact oxidation, water quality parameters according to the general quality of life, the influent BOD200mg/1, the design of water index BOD200mg/1,
    There are six components in total: the regulating pool; the contact oxidation pool; the two sink; the disinfector; the sludge treatment machine; the fan,
    
    The following details of each unit of the sewage treatment equipment are described in detail.
    The primary settling tank: the primary settling tank for vertical flow sedimentation tank of sewage in the deep pool rising velocity is 0.6-0.7 mm / s, let the big granular sludge settling down, reduce the load of biological treatment, the sludge through the sludge sedimentation pipe to realize the regulation pool, once again cycle processing;
    2, contact oxidation pond: after the initial sedimentation, the water flows to the contact pool for biochemical treatment. The contact pool is divided into three stages, with a total residence time of 1 hours or more. The contact oxidation time of the enhanced equipment can reach 6 hours, and the filler is novel filler, easy to conjunctival and not clogged. The specific surface area of the packing is 160m2/m3, and the ratio of air to water in the contact pool is about 12:1.
    3, two sink pool: biochemical sewage flow to two sink pool, two sink pool to two vertical flow sedimentation tank, they run in parallel. The rising flow rate is 0.3-0.4 mm / sec. The sludge is raised to the sludge device by air.
    4, disinfection pond device: disinfection pool according to specification: "TJ14-74" standard for 30 minutes, if hospital sewage, disinfection pool can increase residence time to 1-1.5 hours, use solid chlorine tablet contact dissolution of disinfection. The disinfection device can constantly change the dosage according to the size of the water discharge, so as to achieve the purpose of adding more water and adding medicine, less water and less medicine. Other disinfection devices can be prepared separately.
    5, the sludge sludge supernatant pool device: return to the heat exchange oxidation pool for processing, the digested sludge rarely, usually 1-2 years cleaning time, cleaning method by inspection hole tumbril from the sludge tank into the sludge at the bottom of the suction sinotrans. It can also be treated by recycling.
    6, fan: the fan is located above the disinfectant, the inlet adopts double-layer sound insulation, and there is muffler and fan filter in the inlet, so there is no noise in operation. The operation life of the single typhoon machine is about 30000 hours.
    
    The application characteristics of domestic sewage treatment equipment:
    (1) scope of application: it is suitable for domestic sewage treatment and similar industrial sewage treatment in residential areas, restaurants, hotels, sanatorium, schools, mines and factories.
    (2): BOD5, characteristics of the equipment set COD, NH3-N, Escherichia coli, PH can be installed in a body; the surface of sewage treatment equipment, can also be buried underground; the low noise smell less, the impact on the surrounding environment; a high degree of purification of the entire system, the amount of sludge produced less high degree of automation;, the management is convenient, does not require special management; the technology is stable, convenient maintenance and low energy consumption, save the operation cost.
    (3) specifications: production of Qingzhiyuan sewage treatment equipment, has a fixed size integration of six types of equipment; and according to the sewage water or water quality of complete sets of equipment design and manufacture.
    Process Description: (4) the design of wastewater treatment facilities is mainly domestic sewage and similar industrial organic wastewater treatment, the main approach is the use of biochemical treatment of mature biological contact oxidation method, the water quality parameters calculated in accordance with the general sewage water quality design, the average BOD5 value is 200mg/L, the effluent the average value of BOD5 is 20mg/L.
    A, hydrolysis adjustment pool is not in the equipment, needs the user to build, the pool must install the coarse, fine grille each one, in order to intercept the coarse slag and the larger suspended substance in the sewage.
    B and biological contact oxidation tank are filled with composite packing in the middle part, and SLB type jet aerator 2 units at the bottom, one for timing automatic aeration and one for lifting pump linkage.
    C, for the inclined plate sedimentation tank, tank inlet and outlet pipe with multi row hole distribution and catchment, the water stable state; the bottom of the pool for the "V" type inclined bottom and is provided with two perforated sludge discharge pipe, sludge tank every 3-6 months from the pump truck or out of sinotrans.

    http://jnttjx01.cn.b2b168.com
    欢迎来到济宁市天通机械设备有限公司网站, 具体地址是山东省济宁任城区唐口工业园,老板是尹宜良。 主要经营济宁 天通,是国内成员之一的机械设备加工生产研发厂家,其核心技术以:智能自动化小型压路机、数控钢筋笼滚焊机、公路拌合机机械设备为主。 济宁 天通,始终坚持以“先做人,后做事”为核心价值观,以“儒商文化”为品牌文化,以“做今日品牌,创**企业”为宗旨,以“实用为本、德行天下”为理念,铸造中国机械行业的**品牌。公司依托与国外的分支机构、国内的办事处、及专业的施工队伍,凭借行业内设备研发*团队的强大创。 单位注册资金单位注册资金人民币 100 - 250 万元。 我司专营小型压路机,灰土拌和机,拖拽式小宝马拌和机,手扶压路机,钢筋笼滚焊机,研发团队成员,均来自国内外大型工程机械企业的研发机构的专业技术人员。经过多年的实践与积累,掌握了多种工程机械产品从设计到生产加工的全套技术。